CWE-1392

The Four-Faith router models F3x24 and F3x36 are affected by an operating system (OS) command injection vulnerability. At least firmware version 2.0 allows authenticated and remote attackers to execute arbitrary OS commands over HTTP when modifying the system time via apply.cgi. Additionally, this firmware version has default credentials which, if not changed, would effectively change this vulnerability into an unauthenticated and remote OS command execution issue.

Tattile Smart+, Vega, and Basic device families firmware versions 1.181.5 and prior ship with default credentials that are not forced to be changed during installation or commissioning. An attacker who can reach the management interface can authenticate using the default credentials and gain administrative access, enabling unauthorized access to device configuration and data.

JAIOTlink C492A-W6 Wi-Fi IP cameras running firmware 4.8.30.57701411 contain a hard-coded credentials vulnerability that allows network-adjacent attackers to gain unauthorized access by using the default admin username with an empty password accepted by the anyka_ipc HTTP service on port 80. Attackers can authenticate with these hardcoded credentials to access camera snapshots, video streams, network configuration, and factory-level API endpoints including the SetMAC command injection surface.

Default credential in install package in ABB ASPECT; NEXUS Series; MATRIX Series version 3.07 allows attacker to login to product instances wrongly configured.

A vulnerability classified as critical has been found in Sony SNC-M1, SNC-M3, SNC-RZ25N, SNC-RZ30N, SNC-DS10, SNC-CS3N and SNC-RX570N up to 1.30. This affects an unknown part of the component Administrative Interface. The manipulation leads to use of default credentials. It is possible to initiate the attack remotely. The complexity of an attack is rather high. The exploitability is told to be difficult. The exploit has been disclosed to the public and may be used. The real existence of this vulnerability is still doubted at the moment. It is recommended to change the configuration settings. The vendor was contacted early about this issue. They confirmed the existence but pointed out that they "have published the 'Hardening Guide' on the Web from July 2018 to January 2025 and have thoroughly informed customers of the recommendation to change their initial passwords".

A vulnerability was found in SourceCodester Employee Management System 1.0. It has been rated as critical. Affected by this issue is some unknown functionality of the file index.php. The manipulation of the argument username/password leads to use of default credentials. The attack may be launched remotely. The exploit has been disclosed to the public and may be used.

All versions of the qBittorrent client through 4.5.5 use default credentials when the web user interface is enabled. The administrator is not forced to change the default credentials. As of 4.5.5, this issue has not been fixed. A remote attacker can use the default credentials to authenticate and execute arbitrary operating system commands using the "external program" feature in the web user interface. This was reportedly exploited in the wild in March 2023.

PTZOptics and possibly other ValueHD-based pan-tilt-zoom cameras use default, shared credentials for the administrative web interface.

Hitron Technologies CODA-5310 Telnet function with the default account and password, and there is no warning or prompt to ask users to change the default password and account. An unauthenticated remote attackers can exploit this vulnerability to obtain the administrator’s privilege, resulting in performing arbitrary system operation or disrupt service.

Care Everywhere Gateway 14.3.10 contains a hard-coded credentials vulnerability in the bundled WildFly 8.2.0.Final management interface that allows unauthenticated remote attackers to gain administrative access by using default credentials identical across all installations. Attackers can authenticate to the exposed WildFly management console on port 20990 and deploy a malicious Web Application Archive file through the Deployments interface to achieve remote code execution as the Windows machine account. Version 14.x.x was declared end-of-life (EOL) in 2017 and future releases have addressed the vulnerable finding.

AutoBangumi before 3.2.8 contains a hard-coded default credentials vulnerability that allows unauthenticated attackers to authenticate as the administrator by using the publicly known default credentials seeded at startup via add_default_user() in the database user module when the users table is empty. Attackers can submit the default credentials to the authentication login endpoint to gain full control of the application, including RSS feed configuration, downloader configuration, and all authenticated API endpoints.

IBM Sterling Connect:Direct Web Services 6.0, 6.1, 6.2, and 6.3 uses default credentials for potentially critical functionality.

A vulnerability was found in 70mai M300 up to 20250611 and classified as critical. Affected by this issue is some unknown functionality of the component Telnet Service. The manipulation leads to use of default credentials. The attack needs to be initiated within the local network. The exploit has been disclosed to the public and may be used. The vendor was contacted early about this disclosure but did not respond in any way.

iMonitor EAM 9.6394 ships with default administrative credentials that are also displayed within the management client’s connection dialog. If the administrator does not change these defaults, a remote attacker can authenticate to the EAM server and gain full control over monitored agents and data. This enables reading highly sensitive telemetry (including keylogger output) and issuing arbitrary actions to all connected clients.

A vulnerability has been found in 70mai X200 up to 20251010. Affected by this vulnerability is an unknown functionality of the component HTTP Web Server. The manipulation leads to use of default credentials. The attack can be initiated remotely. The exploit has been disclosed to the public and may be used. The vendor was contacted early about this disclosure but did not respond in any way.

eNet SMART HOME server 2.2.1 and 2.3.1 ships with default credentials (user:user, admin:admin) that remain active after installation and commissioning without enforcing a mandatory password change. Unauthenticated attackers can use these default credentials to gain administrative access to sensitive smart home configuration and control functions.

A vulnerability was identified in TRENDnet TI-G160i, TI-PG102i and TPL-430AP up to 20250724. This affects an unknown part of the component SSH Service. The manipulation leads to use of default credentials. It is possible to initiate the attack remotely. The exploit has been disclosed to the public and may be used. The real existence of this vulnerability is still doubted at the moment. The vendor explains: "For product TI-PG102i and TI-G160i, by default, the product's remote management options are all disabled. The root account is for troubleshooting purpose and the password is encrypted. However, we will remove the root account from the next firmware release. For product TPL-430AP, the initial setup process requires user to set the password for the management GUI. Once that was done, the default password will be invalid."

Default credentials on the Web Interface of Evolution Controller 2.x allows anyone to log in to the server directly to perform administrative functions. Upon installation or upon first login, the application does not ask the user to change the password. There is no warning or prompt to ask the user to change the default password.

A vulnerability, which was classified as critical, was found in Fanli2012 native-php-cms 1.0. This affects an unknown part of the file /fladmin/user_recoverpwd.php. The manipulation leads to use of default credentials. It is possible to initiate the attack remotely. The exploit has been disclosed to the public and may be used.

A vulnerability was found in Edimax BR-6208AC 2_1.02. The affected element is the function auth_check_userpass2. Performing a manipulation of the argument Username/Password results in use of default credentials. The attack may be initiated remotely. The exploit has been made public and could be used. The vendor confirms that the affected product is end-of-life. They confirm that they "will issue a consolidated Security Advisory on our official support website." This vulnerability only affects products that are no longer supported by the maintainer.

A weakness has been identified in Ziroom ZHOME A0101 1.0.1.0. Impacted is an unknown function of the component Dropbear SSH Service. This manipulation causes use of default credentials. Remote exploitation of the attack is possible. The complexity of an attack is rather high. The exploitability is considered difficult. The exploit has been made available to the public and could be used for attacks. The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability has been identified in SIMATIC CN 4100 (All versions < V2.7). The "intermediate installation" system state of the affected application uses default credential with admin privileges. An attacker could use the credentials to gain complete control of the affected device.

Insecure default credentials for the Adminsitrator account of D-Link DSL-7740C with firmware DSL7740C.V6.TR069.20211230 allows attackers to escalate privileges via a bruteforce attack.

A vulnerability was found in China Mobile P22g-CIac, ZXWT-MIG-P4G4V, ZXWT-MIG-P8G8V, GT3200-4G4P and GT3200-8G8P up to 20250305. It has been rated as critical. This issue affects some unknown processing of the component CLI su Command Handler. The manipulation leads to use of default credentials. The attack may be initiated remotely. The exploit has been disclosed to the public and may be used. The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability has been identified in SIPROTEC 5 6MD84 (CP300) (All versions < V9.90), SIPROTEC 5 6MD85 (CP300) (All versions >= V8.80 < V9.90), SIPROTEC 5 6MD86 (CP300) (All versions >= V8.80 < V9.90), SIPROTEC 5 6MD89 (CP300) (All versions >= V8.80 < V9.90), SIPROTEC 5 6MD89 (CP300) V9.6x (All versions < V9.68), SIPROTEC 5 6MU85 (CP300) (All versions >= V8.80 < V9.90), SIPROTEC 5 7KE85 (CP300) (All versions >= V8.80 < V10.0), SIPROTEC 5 7SA82 (CP150) (All versions < V9.90), SIPROTEC 5 7SA86 (CP300) (All versions >= V8.80 < V9.90), SIPROTEC 5 7SA87 (CP300) (All versions >= V8.80 < V9.90), SIPROTEC 5 7SD82 (CP150) (All versions < V9.90), SIPROTEC 5 7SD86 (CP300) (All versions >= V8.80 < V9.90), SIPROTEC 5 7SD87 (CP300) (All versions >= V8.80 < V9.90), SIPROTEC 5 7SJ81 (CP150) (All versions < V9.90), SIPROTEC 5 7SJ82 (CP150) (All versions < V9.90), SIPROTEC 5 7SJ85 (CP300) (All versions >= V8.80 < V9.90), SIPROTEC 5 7SJ86 (CP300) (All versions >= V8.80 < V9.90), SIPROTEC 5 7SK82 (CP150) (All versions < V9.90), SIPROTEC 5 7SK85 (CP300) (All versions >= V8.80 < V9.90), SIPROTEC 5 7SL82 (CP150) (All versions < V9.90), SIPROTEC 5 7SL86 (CP300) (All versions >= V8.80 < V9.90), SIPROTEC 5 7SL87 (CP300) (All versions >= V8.80 < V9.90), SIPROTEC 5 7SS85 (CP300) (All versions >= V8.80 < V9.90), SIPROTEC 5 7ST85 (CP300) (All versions >= V8.80 < V10.0), SIPROTEC 5 7ST85 (CP300) V9.6x (All versions < V9.68), SIPROTEC 5 7ST86 (CP300) (All versions < V10.0), SIPROTEC 5 7ST86 (CP300) V9.8x (All versions < V9.83), SIPROTEC 5 7SX82 (CP150) (All versions < V9.90), SIPROTEC 5 7SX85 (CP300) (All versions >= V8.80 < V9.90), SIPROTEC 5 7SY82 (CP150) (All versions < V9.90), SIPROTEC 5 7UM85 (CP300) (All versions >= V8.80 < V9.90), SIPROTEC 5 7UT82 (CP150) (All versions < V9.90), SIPROTEC 5 7UT85 (CP300) (All versions >= V8.80 < V9.90), SIPROTEC 5 7UT86 (CP300) (All versions >= V8.80 < V9.90), SIPROTEC 5 7UT87 (CP300) (All versions >= V8.80 < V9.90), SIPROTEC 5 7VE85 (CP300) (All versions >= V8.80 < V9.90), SIPROTEC 5 7VK87 (CP300) (All versions >= V8.80 < V9.90), SIPROTEC 5 7VU85 (CP300) (All versions < V9.90), SIPROTEC 5 Communication Module ETH-BA-2EL (Rev.2) (All versions < V9.90), SIPROTEC 5 Communication Module ETH-BA-2EL (Rev.2) V9.6 (All versions < V9.68), SIPROTEC 5 Communication Module ETH-BA-2EL (Rev.2) V9.8 (All versions < V9.83), SIPROTEC 5 Communication Module ETH-BB-2FO (Rev. 2) (All versions < V9.90), SIPROTEC 5 Communication Module ETH-BB-2FO (Rev. 2) V9.6 (All versions < V9.68), SIPROTEC 5 Communication Module ETH-BB-2FO (Rev. 2) V9.8 (All versions < V9.83), SIPROTEC 5 Communication Module ETH-BD-2FO (All versions >= V8.80 < V9.90), SIPROTEC 5 Communication Module ETH-BD-2FO V9.6 (All versions < V9.68), SIPROTEC 5 Communication Module ETH-BD-2FO V9.8 (All versions < V9.83), SIPROTEC 5 Compact 7SX800 (CP050) (All versions >= V9.50 < V9.90). Affected devices do not properly validate SNMP GET requests. This could allow an unauthenticated, remote attacker to retrieve sensitive information of the affected devices with SNMPv2 GET requests using default credentials.

NETGEAR ProSAFE Network Management System Default Credentials Local Privilege Escalation Vulnerability. This vulnerability allows local attackers to escalate privileges on affected installations of NETGEAR ProSAFE Network Management System. An attacker must first obtain the ability to execute low-privileged code on the target system in order to exploit this vulnerability. The specific flaw exists within the product installer. The issue results from the use of default MySQL credentials. An attacker can leverage this vulnerability to escalate privileges and execute arbitrary code in the context of SYSTEM. Was ZDI-CAN-22755.

Ilevia EVE X1 Server firmware versions ≤ 4.7.18.0.eden contain a use of default credentials vulnerability that allows an unauthenticated attacker to obtain remote access. Ilevia has declined to service this vulnerability, and recommends that customers not expose port 8080 to the internet.

A vulnerability classified as critical was found in Tosei Online Store Management System ネット店舗管理システム 4.02/4.03/4.04. This vulnerability affects unknown code of the component Backend. The manipulation leads to use of default credentials. The attack can be initiated remotely. The exploit has been disclosed to the public and may be used. NOTE: The vendor was contacted early about this disclosure but did not respond in any way.

Austrian Archaeological Institute (AI) OpenAtlas v8.11.0 as discovered to contain a hardcoded Administrator password.

Use of Default Credentials vulnerability in Tananaev Solutions Traccar Server on Administrator Panel modules allows Authentication Abuse.This issue affects the privileged transactions implemented by the Traccar solution that should otherwise be protected by the authentication mechanism.  These transactions could have an impact on any sensitive aspect of the platform, including Confidentiality, Integrity and Availability.

A flaw was found in Skupper. When Skupper is initialized with the console-enabled and with console-auth set to Openshift, it configures the openshift oauth-proxy with a static cookie-secret. In certain circumstances, this may allow an attacker to bypass authentication to the Skupper console via a specially-crafted cookie.

Proscend Advice ICR Series routers FW version 1.76 - CWE-1392: Use of Default Credentials

A remote unauthenticated attacker can use the firmware update feature on the LAN interface of the device to reset the password for the predefined, low-privileged user “user-app” to the default password.

OpenProject is open-source, web-based project management software. Prior to , the official openproject/openproject Docker image ships ENV SECRET_KEY_BASE=OVERWRITE_ME as the default Rails master key. Combined with cookies_serializer = :marshal, this gives any logged-in user a deterministic Marshal-deserialization path reachable via the /my/two_factor_devices cookie reader This vulnerability is fixed in .

netbox-docker before 2.5.0 has a superuser account with default credentials (admin password for the admin account, and 0123456789abcdef0123456789abcdef01234567 value for SUPERUSER_API_TOKEN). In practice on the public Internet, almost all users changed the password but only about 90% changed the token. Having a default token value was intentional and was valuable for the main intended use case of the netbox-docker product (isolated development networks). Some users engaged in an effort to repurpose netbox-docker for production. The documentation for this effort stated that the defaults must not be used. However, installation did not ensure non-default values. The Supplier was aware of the CVE ID assignment and did not object to the assignment.

If misconfigured, alpitronic Hypercharger EV charging devices can expose a web interface protected by authentication. If the default credentials are not changed, an attacker can use public knowledge to access the device as an administrator.

Tyler Identity Local (TID-L) uses documented, default administrative credentials. Users are not required to change the credentials before deployment. TID-L has not been distributed since December 2020, and has not been supported since 2021.

A vulnerability, which was classified as problematic, has been found in elunez eladmin up to 2.7. Affected by this issue is some unknown functionality of the file eladmin-system\src\main\resources\config\application-prod.yml of the component Druid. The manipulation of the argument login-username/login-password leads to use of default credentials. The attack may be launched remotely. The exploit has been disclosed to the public and may be used.

Gardyn Home Kit firmware before master.619, Home Kit Mobile Application before 2.11.0, and Home Kit Cloud API before 2.12.2026 use weak default credentials for secure shell access. This may result in attackers gaining access to exposed Gardyn Home Kits.

File Browser provides a file managing interface within a specified directory and it can be used to upload, delete, preview, rename and edit files. Prior to version 2.34.1, a missing password policy and brute-force protection makes the authentication process insecure. Attackers could mount a brute-force attack to retrieve the passwords of all accounts in a given instance. This issue has been patched in version 2.34.1.

The TELNET service of AdTran NetVanta 3120 18.01.01.00.E devices is enabled by default, and has default credentials for a root-level account.

SODOLA SL902-SWTGW124AS firmware versions through 200.1.20 contain a default credentials vulnerability that allows remote attackers to obtain administrative access to the management interface. Attackers can authenticate using the hardcoded default credentials without password change enforcement to gain full administrative control of the device.

Nornicdb is a distributed low-latency, Graph+Vector, Temporal MVCC with all sub-ms HNSW search, graph traversal, and writes. Prior to version 1.0.42-hotfix, the --address CLI flag (and NORNICDB_ADDRESS / server.host config key) is plumbed through to the HTTP server correctly but never reaches the Bolt server config. The Bolt listener therefore always binds to the wildcard address (all interfaces), regardless of what the user configures. On a LAN, this exposes the graph database — with its default admin:password credentials — to any device sharing the network. This issue has been patched in version 1.0.42-hotfix.

Austrian Archaeological Institute (AI) OpenAtlas v8.11.0 as discovered to contain a SQL injection vulnerability.

SAP Commerce Cloud could retain a sample OAuth2 client with publicly documented sample credentials originating from sample configuration provided in SAP Help Portal documentation. If left unchanged, an unauthenticated attacker could use these well-known credentials to obtain a valid access token and invoke certain APIs to read and modify data. Successful exploitation results in high impact on confidentiality and integrity, with no impact on availability.

Airship AI Acropolis includes a default administrative account that uses the same credentials on every installation. Instances of Airship AI that do not change this account password are vulnerable to a remote attacker logging in and gaining the privileges of this account. Fixed in 10.2.35, 11.0.21, and 11.1.9.

A vulnerability was found in yangzongzhuan RuoYi up to 4.8.1. It has been classified as problematic. Affected is an unknown function of the file ruoyi-admin/src/main/resources/application-druid.yml of the component Druid. The manipulation leads to use of default credentials. It is possible to launch the attack remotely. The exploit has been disclosed to the public and may be used.

Fedora Repository 3.8.x includes a service account (fedoraIntCallUser) with default credentials and privileges to read read local files by manipulating datastreams. Fedora Repository 3.8.1 was released on 2015-06-11 and is no longer maintained. Migrate to a currently supported version (6.5.1 as of 2025-01-23).

MOBATIME Network Master Clock - DTS 4801 allows attackers to use SSH to gain initial access using default credentials.

IBM API Connect 12.1.0.0 through 12.1.0.3 uses default credentials which could allow an attacker to gain unauthorized access to the application before the system enforces a credential update.

JM-DATA ONU JF511-TV version 1.0.67 uses default credentials that allow attackers to gain unauthorized access to the device with administrative privileges.

An issue was discovered on G-Net Dashcam BB GONX devices. Default credentials for SSID cannot be changed. It broadcasts a fixed SSID with default credentials that cannot be changed. This allows any nearby attacker to connect to the dashcam's network without restriction. Once connected, an attacker can sniff on connected devices such as the user's smartphone. The SSID is also always broadcasted.

LazyOwn RedTeam/APT Framework is an AI-powered C2 and red-team operations framework. Prior to 0.2.154, LazyOwn ships default C2 credentials LazyOwn and LazyOwn in payload.json and core/payload_schema.py and passes them unchanged to lazyc2.py HTTP Basic authentication, allowing any network-reachable attacker who knows the defaults to authenticate to the C2 dashboard with operator-level access. This issue is fixed in 0.2.154.

OpenMQ exposes a TCP-based management service (imqbrokerd) that by default requires authentication. However, the product ships with a default administrative account (admin/ admin) and does not enforce a mandatory password change on first use. After the first successful login, the server continues to accept the default password indefinitely without warning or enforcement. In real-world deployments, this service is often left enabled without changing the default credentials. As a result, a remote attacker with access to the service port could authenticate as an administrator and gain full control of the protocol’s administrative features.

By default, the password for the Access Manager's web interface, is set to 'admin'. In the tested version changing the password was not enforced.

Aten PE6208 2.3.228 and 2.4.232 have default credentials for the privileged web interface account. The user is not asked to change the credentials after first login. If not changed, attackers can log in to the web interface and gain administrator privileges.

IO-1020 Micro ELD web server uses a default password for authentication.

NetBird VPN when installed using vendor's provided script failed to remove or change default password of an admin account created by ZITADEL. This issue affects instances installed using vendor's provided script. This issue may affect instances created with Docker if the default password was not changed nor the user was removed. This issue has been fixed in version 0.57.0

Istio is an open platform to connect, manage, and secure microservices. Prior to 1.29.1, 1.28.5, and 1.27.8, a user of Istio is impacted if the JWKS resolver becomes unavailable or the fetch fails, exposing hardcoded defaults regardless of use of the RequestAuthentication resource. This vulnerability is fixed in 1.29.1, 1.28.5, and 1.27.8.

Microhard Systems IPn4G 1.1.0 contains hardcoded default credentials that cannot be changed through normal gateway operations. Attackers can exploit these default credentials to gain unauthorized root-level access to the device by logging in with predefined username and password combinations.

The Thermo Fisher Torrent Suite Django application 5.18.1 has weak default credentials, which are stored as fixtures for the Django ORM API. The ionadmin user account can be used to authenticate to default deployments with the password ionadmin. The user guide recommends changing default credentials; however, a password change policy for default administrative accounts is not enforced. Many deployments may retain default credentials, in which case an attacker is likely to be able to successfully authenticate with administrative privileges.

COMMAX CVD-Axx DVR 5.1.4 contains weak default administrative credentials that allow remote password attacks and disclose RTSP stream. Attackers can exploit this by sending a POST request with the 'passkey' parameter set to '1234', allowing them to access the web control panel.

Dell ECS, versions 3.8.1.0 through 3.8.1.7, and Dell ObjectScale versions prior to 4.2.0.0, contains an Use of Default Credentials vulnerability in the OS. A low privileged attacker with remote access could potentially exploit this vulnerability, leading to Elevation of privileges.

Adtec Digital SignEdje Digital Signage Player v2.08.28 contains multiple hardcoded default credentials that allow unauthenticated remote access to web, telnet, and SSH interfaces. Attackers can exploit these credentials to gain root-level access and execute system commands across multiple Adtec Digital product versions.

Legacy Vivotek Device firmware uses default credetials for the root and user login accounts.

CWE-1392: Use of Default Credentials

Agiloft Release 28 contains several accounts with default credentials that could allow local privilege escalation. The password hash is known for at least one of the accounts and the credentials could be cracked offline. Users should upgrade to Agiloft Release 30.

Multiple services of the DUT as well as different scopes of the same service reuse the same credentials.

A CWE-1392 “Use of Default Credentials” was discovered affecting the 130.8005 TCP/IP Gateway running firmware version 12h. The device exposes an FTP server with default and easy-to-guess admin credentials. A remote attacker capable of interacting with the FTP server could gain access and perform changes over resources exposed by the service such as configuration files where password hashes are saved or where network settings are stored.

The product does not require unique and complex passwords to be created during installation. Using Philips's default password could jeopardize the PACS system if the password was hacked or leaked. An attacker could gain access to the database impacting system availability and data integrity.

Default credentials in Ivanti Cloud Services Application before version 5.0.5 allows a local authenticated attacker to escalate their privileges.

IO-1020 Micro ELD uses a default WIFI password that could allow an adjacent attacker to connect to the device.

HAX CMS NodeJS allows users to manage their microsite universe with a NodeJS backend. Versions 11.0.9 and below were distributed with hardcoded default credentials for the user and superuser accounts. Additionally, the application has default private keys for JWTs. Users aren't prompted to change credentials or secrets during installation, and there is no way to change them through the UI. An unauthenticated attacker can read the default user credentials and JWT private keys from the public haxtheweb GitHub repositories. These credentials and keys can be used to access unconfigured self-hosted instances of the application, modify sites, and perform further attacks. This is fixed in version 11.0.10.

Authentication credentials leakage vulnerability in Hitachi Ops Center Common Services within Hitachi Ops Center OVA. This issue affects Hitachi Ops Center Common Services: from 10.9.3-00 before 11.0.3-00; Hitachi Ops Center OVA: from 10.9.3-00 before 11.0.2-01.

Use of default credentials in Datiphy Data Management Center from v8.3.0 through v8.5.1 allows a remote attacker to gain administrative access to the management platform by logging in with default administrator credentials.

DASAN GPON ONU H660WM OS version H660WMR210825 Hardware version DS-E5-583-A1 was discovered to contain insecure default credentials in the modem's control panel.

Hitachi Ops Center Common Services within Hitachi Ops Center Analyzer viewpoint OVF contains an authentication credentials leakage vulnerability.This issue affects Hitachi Ops Center Common Services: from 10.0.0-00 before 11.0.0-04; Hitachi Ops Center Analyzer viewpoint OVF: from 10.0.0-00 before 11.0.0-04.

A vulnerability was found in IROAD Dash Cam X5 up to 20250203. It has been rated as problematic. This issue affects some unknown processing of the component SSID. The manipulation leads to use of default credentials. The attack needs to be initiated within the local network. The complexity of an attack is rather high. The exploitation is known to be difficult. The exploit has been disclosed to the public and may be used. The vendor was contacted early about this disclosure but did not respond in any way.

Weak Default Credentials.This issue affects BLU-IC2: through 1.19.5; BLU-IC4: through 1.19.5.

SNMP Default Community String (public).This issue affects BLU-IC2: through 1.19.5; BLU-IC4: through 1.19.5.

All the Toshiba printers share the same hardcoded root password. As for the affected products/models/versions, see the reference URL.

RustFS is a distributed object storage system built in Rust. Prior to 1.0.0-beta.2, the internode RPC layer authenticates every request with an HMAC-SHA256 signature using a shared secret. The function that produces this secret, get_shared_secret() in crates/ecstore/src/rpc/http_auth.rs, falls back to the public, source-tree-embedded DEFAULT_SECRET_KEY = "rustfsadmin" when neither the RUSTFS_RPC_SECRET environment variable nor the global S3 secret key has been configured. This vulnerability is fixed in 1.0.0-beta.2.

IBM Cloud Pak for Data System - Cyclops 11.3.0.2 through Interim Fix 002 IBM Cloud Pak for Data System uses default passwords default passwords from the manufacturing process for use during the installation process, which could allow an attacker to bypass authentication.

Authentication credentials leakage vulnerability in Hitachi Ops Center Analyzer viewpoint.This issue affects Hitachi Ops Center Analyzer viewpoint: from 10.0.0-00 before 11.0.4-00.

Sitecom WLX-2006 Wall Mount Range Extender N300 v.1.5 and before is vulnerable to Use of Default Credentials.

A vulnerability was found in Thinkware Car Dashcam F800 Pro up to 20250226. It has been declared as problematic. This vulnerability affects unknown code of the component Device Registration Handler. The manipulation leads to use of default credentials. It is possible to launch the attack on the physical device. The complexity of an attack is rather high. The exploitation appears to be difficult. The exploit has been disclosed to the public and may be used. The vendor was contacted early about this disclosure but did not respond in any way.

Use of default credentials vulnerability in Roche Diagnostics navify Digital Pathology (RabbitMQ Management interface modules) allows Default Usernames and Passwords. This issue affects navify Digital Pathology: from 2.0.0 before 2.4.1.

Prior to 2025-11-03, well-intended users of Terraform or REST API for Google Cloud AlloyDB for PostgreSQL could have created clusters with an insecure default password which could have been exploited by a remote attacker to gain full administrative access to the database. Exploitation required network access to the AlloyDB cluster and was limited to Terraform or the REST API, as other clients blocked it.